Bluzka Baza opis.pdf

burda Download-Pattern,

T-Shirt 3197- instructions

PATTERN

1 Front piece 1x

CUTTING OUT

2 Back piece 1x

3 Sleeve 2x

FOLD (– – – –) means: here is the center of a pattern

piece but never a cut edge or a seam. The piece should be

cut double, with the fold line forming the centre line.

Pattern pieces that are outlined with a broken line in the

cutting diagrams are to be placed face down on the fabric.

4 Front trimming 1x

5 Back trimming 1x

The cutting diagrams on the pattern sheet show how

the pattern pieces should be placed on the fabric.

Paper cut for ANSI A (German DIN A4) prints :

The patterns are printed out on 20 sheets with a thin

frame. Wait, until all sheets are printed out. Arrange the

sheets so that they fit together (see extra page with the

overview of the prints). Cut off the single sheets on the

upper and right edge along the thin frame lines. Begin

with the left lower sheet and then glue the parts in the

frame lines together precisely.

Select your size according to the Burda-dimension table:

Dresses, blouses, jackets and coats according to the bust

size, trousers and skirts according to the hip width.

Change the patterns according to size (inches or cm) if

necessary, to fit your measurements if they deviate from

the Burda-dimension table.

For a single layer of fabric, the pattern pieces are pinned

to the right side of the fabric. For double layers of fabric,

the right sides are facing and the pattern pieces are pinned

to the left side. The pattern pieces that are shown in the

cutting diagram, extending over the fold of the fabric,

should be cut last from a single layer of fabric.

Important: Trim the skirt pattern pieces from the single

layer of fabric, the pattern pieces are pinned to the right

side of the fabric, the labeled pattern side on top = see

cutting diagram

SEAM AND HEMLINE ALLOWANCES are

included on an average:

5/8” (1.5 cm) for all edges and seams. Use BURDA

carbon paper to transfer all pattern lines and markings to

the left side of the fabric pieces. You will find

instructions in the packet.

Cut out the pattern according to your size.

Interfacing

Cut interfacing according to the drawing and

press onto the left fabric side

SEWING

When sewing the right fabric sides are

facing.

Transfer all lines on the pattern using a

basting stitch to the right fabric side.

Tips for working with stretchable fabrics

The optimal result from working with

stretchy fabrics will be achieved by using an

overlock-machine. Seams will become very

elastic and more durable, and will not break

when wearing the finished clothes. If you are

not going to use an over-lock machine, stitch

the seams using an elastic special stitch or a

narrowly adjusted zig-zag stitch. Please take

care that the thread tension is not set too

high. For delicate mesh fabrics it is

necessary to use a Jersey needle for stitching

with your sewing machine.

1) Fold edges, for stitching of the edges (e.g.

at the hem) use a twin needle. Stitch along

the right fabric side using two upper threads

and one under thread, using the straight stitch

setting. In this case the under thread will

appear as zig zag stitch. The result will be

that the fabric will not stretch when sewing

and the seam will be elastic.

SHIRT

Shoulder seams

2) Position front piece on top of the back

piece, right sides facing (seam 1). Trim

allowances, neaten altogether and fold and

press inwards towards the back piece.

Neckline / Facing

3) Position the front facing onto the back

facing right side to right, stitch shoulder

seams (seam 2). Neaten edge.

4) Pin facings onto the neckline right side to

right, shoulder seams meet. Baste trimming

and stitch. Trim allowances and cut in to

make the neckline more flexible.

5) Fold inside and baste facing, press. Stitch

neckline 1/2”(1.5 cm) wide from the edge.

Side seams

6) Position front piece onto the back piece,

right sides facing, baste side seams (seam 3)

and stitch. Trim allowances, neaten

altogether and fold and press inwards

towards the back piece.

Sleeves

7) Fold sleeve lengthwise, right sides

inwards. Baste sleeve seams (seam 4) and

stitch. Trim allowances, neaten altogether,

fold and press inwards towards the back

piece.

Sleeve seam

8) Fold and baste sleeve hem, press. Stitch

bottom sleeve edge using a twin needle

approximately 1” (2.5 cm) wide, baste the

seam simultaneously (see text and drawing

1).

Apply sleeves

9) Pin the sleeves onto the armhole right

sides facing. 3 points are essential for the fit

of the sweater when you apply the sleeves:

= the notch 5 of the top sleeve and the front

piece have to meet. Sleeve seams and side

seams have to meet. The notch of the sleeve

rounding has to meet the shoulder seam.

Baste and stitch the sleeve from the view of

the sleeve side. Trim allowances, neaten

altogether and press inwards into the sleeve.

Stitch hem according to the text and drawing

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: