NMEA0183 to RS-232 RS-422 or RS-485 Model 183COR.pdf

183COR1595 - pg. 1/2

NMEA0183 to RS-232/RS-422 or RS-485

Model 183COR

Document No. 183COR1595

Description:

The 183COR converts one NMEA0183 Version one data signal to either RS-232, RS-422, or RS-485 voltage levels. It also

converts one data signal coming from any of the three EIA Specifications to NMEA0183 voltage levels. The unit can be powered

externally by a wide DC voltage range that is brought in on a pair of stripped and tinned wire leads. The RS-232, RS-422, and RS-

485 signals are provided on the same DB-25 female connector, and the NMEA0183 signals are provided on a DB-25 male connector.

NMEA0183 is a standard which describes both the electrical characteristics and the software protocol that should be used

for interfacing electronic marine navigational devices. Version one is an older standard, but many devices are still in use that comply

with these specifications. Electrically, this standard is an unbalanced signal similar to RS-232, but with higher current handling

capabilities and optical isolation on the receive line.

RS-232/RS-422/RS-485 Side:

Connector: DB-25 Female

Signals: RS-232 pins configured as a DCE device.

Passes through TD and RD.

RTS and CTS are tied together.

DTR, DSR, and CD are tied together.

RS-422 and RS-485 provided on the same set of pins.

Automatic enable of RS-422/RS-485 driver.

Easily modified for constant enable of 422/485 receiver.

Space provided for optional 422/485 termination.

NMEA0183 Side:

Connector: DB-25 Male

Signals: Passes through TD and RD.

Zero to Eight volt voltage swing on transmitter.

Transmitter capable of sourcing 15mA in active state.

0.5 volts maximum on receiver for idle or marking state.

4 volts minimum on receiver for active or spacing state.

Receiver input impedance is 1.3K ohms.

2000 volts optical isolation on receiver.

Requires 10 to 30 VDC at 100mA.

3.67" X 2.41" X 0.56"

Operation and Connections:

RS-232:

To 25 pin DTE device (computer, pc, terminal, printer) connect pins 2, 3, and 7 straight through.

To 25 pin DCE device (modem) cross pins 2 and 3 connect pin 7 straight through.

All 25 pins can be connected if you wish to use a standard 25 pin to 25 pin cable to a DTE or null modem cable to a DCE.

RS-422 or RS-485 four-wire setup:

RS-485 two-wire setup:

NMEA0183 Connections:

Power Requirements:

Dimensions:

183COR1595 - pg. 2/2

During transmission, the RS-422/RS-485 transmitter is kept enabled for approximately two milliseconds after the

transmission of the last data bit. This is to ensure that no data is cut off at the end of the data stream. This time-out period can be

changed by changing the values of a resistor R13 and capacitor C5 as shown in Table 1.

Space for an optional RS-422/RS-485 termination resistor R16 is provided on the PCBD. This resistor is not normally

placed during manufacturing. If using the 183COR at high data rates or long distances, this space can be used to install a resistor

between the Receive Data A and Receive Data B lines. Normally the value of this termination resistor is 120 ohms to match the

approximate characteristic impedance of the twisted pair wire used. See the RS-422/RS-485 Application Note for more information

on termination.

Figure 1.

Baud

Rate

Time

(ms)

Resistor

R13

(ohm)

Capacitor

(mfd)

300

33.3

33K

600

16.6

16K

1200

8.33

82K

2400

4.16

43K

* 4800

2.08

20K

9600

1.04

10K

19200

0.520

5.6K

38400

0.260

2.7K

56000

0.176

1.6K

115000

0.0868

8.2K

.01

* Default Values

Figure 2.

Table 1.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: