Instalacja modułu Bluetooth w BMW E39.pdf

Table of Contents

Installation instructions for

European Integrated Systems, Ltd.

BMW to Bluetooth ® Wireless

Technology equipped Car-Kit

Interface

1. Introduction

2. BMW Microphone Installation

3. HarnessInstallation

4. HCB-30 Bluetooth Module Installation

5. Configuration/Setup

6. Warranty/DisclaimerInformation

Vehicles covered in this document:

1997 – 2/2002 5 Series Sedans (including DSP

equipped)

Handsfree car-kit:

Sony Ericsson HCB-30

Version r1.3

The Bluetooth word mark and logos are owned by the Bluetooth SIG,

Inc. and any use of such marks by European Integrated Systems, Ltd.

is under license. Other trademarks and trade names are those of their

respective owners.

WWW.EISKITS.COM

Thank you for purchasing our BMW interface. This interface is

designed to partial integration of your BMW’s built in mobile

phone capabilities and your Bluetooth wireless technology

enabled mobile phone. Below is a list of components that you

should have received from us or have purchased separately.

We will then discuss the features and operation of your new

interface.

Section 2. Installation of the BMW

Microphone

Installation of the BMW microphone requires removal of the

overhead console cover so as to access the wiring for the mic.

Below are pictures of the steps for removal of the cover.

You will need the following components to complete the

installation:

•

Interface box

•

Wiring harness with multiple connectors (custom for your car)

Gently pry apart

the overhead light

panel from the

back of the panel

using a small

screwdriver or

other suitable tool

(butter knife).

•

Sony Ericsson HCB-30 or other phone kit

•

BMW Microphone (part number 84 31 8 380 338)

If you purchased your HCB-30 kit through us, the wiring

harness will be ready to go. If you purchased your own, you

will need to connect the four power wires to the harness.

Splice the four wires per the HCB-30 installation manual.

Splicing material not provided by EIS. This kit provides

integration of a Bluetooth wireless technology enabled phone

with the car’s stereo for radio mute and use of the built in BMW

cell phone speakers. The BMW microphone is also utilized.

The steering wheel buttons work for answering a call and

hanging up, as well as activating voice dial and volume control

during a call. The radio display indicates "PHONE" when a call

is in progress (on later model 5 series only). The phone can

be set to automatically connect with the car upon starting the

car (or pressing the unlock button on the key) and the interface

and BMW electronics stay active and connected to your phone

after you turn the car off to allow you to complete a call in

progress. We do not offer support for display of the calling

number on the radio, etc. at this point.

Everything is in the trunk and there are no wires to run. You

also have the advantage that if you are leasing your car you

can re-use the Sony Ericsson portion of the kit with another

brand if you go away from BMW.

WWW.EISKITS.COM

Using just finger

pressure, pull

down the cover

plate that has the

microphone grill

in it.

Here is the mic as you are ready to press it into the grill. Note

that the arrow should point toward the front of the vehicle.

Reinstall the cover and light panel in the reverse

order of removal.

Locate the correct three conductor wire. It will

be a black connector and should have one wire

that in clear in color. Detach the wire from the

cable holders so that you have enough wire to

reach where the mic goes. Connect the

microphone.

WWW.EISKITS.COM

Section 3. Installation of the wiring harness

Lets get to the trunk and locate the cabling you will need to

have access to. On the left side of the trunk is a door that you

would use to change CDs in the CD changer. You may need a

small flathead screwdriver to remove the clips so as to pull

back the cover panel forward of the door to gain access to the

cabling (wrapped in black foam).

Connect

cable and

blue wire to

pin 3

(white/yel) of

3 conductor

cable.

Drivers Side trunk – attach DB25 connector

Just pop open the door for access to the BMW CD changer to

install this. You may wish to add a tie wrap to ensure

permanent attachment.

There is sometimes more than one 3 conductor cable – please

ensure that the color specified is in the connector – if not,

please contact us.

Look for

harness(s) in

this area.

Attach the

other 25 pin

connector to

the EIS

Interface Box

and screw

down.

WWW.EISKITS.COM

Section 4: Module installation

Example

location using

the holes in

the liner

where the

plastic info

buttons were.

There are

many

possible

locations that

will work.

Pictured is a

Nokia kit.

Secure EIS

Box

(locations are

at customers

discretion)

Location of the HCB-30 (or other) BT module is at customers

discretion but it should be placed in a location that will aid in

the communication to the phone.

Clean up and cut tiewraps (not included) and you are ready to

test….

Attach Harness

to the HCB-30

module.

Note the

speaker wire

connection

positions. Red

is on pin 1

(closest to

center of

module).

NOTE:

Please be aware that some E39 5 series cars were delivered

without what is called an “SES jumper plug.” This is a blue

plug that attaches to the blue connector in the same area as the

25 pin black connector you just found for using our interface.

This plug is necessary for your kit to function. It is BMW part

number: 84110018038 and it costs $8.00 to $16.00

It often looks like:

WWW.EISKITS.COM

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: