5L-6L.pdf

AX ENGINE

TECHNICAL

GUIDE

PRINTERS:

HP Laserjet 5L/5ML

HP Laserjet 6LSE/6LXI

HP Laserjet 3100

Canon LBP-460

Canon Laser Class

4000/4500 (FX3)

Step 1

OEM INFORMATION:

Part #: C3906A

Gram Load: 140 grams

Yield @ 5%: 2500

Pages per min: 4 ppm

Resolution (dpi): 600

Place the AX cartridge on a table with

the handle facing up. Using diagonal pliers,

pull the steel lock pin from one end and then

the other (See photo #1). The cartridge sep-

arates into waste hopper and toner hopper

Tools & Supplies Required

Funnel

Diagonal Pliers

Needlenose Pliers

Phillips #2 Screwdriver

Small Flat Blade Screwdriver

140 Grams of 5L Toner

Damp Cloth

Soft Lint-free Cloth

halves. Place the toner hopper aside.

Step 3

Remove the primary charge roller

(PCR) from its clips and set it aside

(See photo #4). Note that this roller is

similar to the 5P in that it has a much

Step 2

more pliable covering than the harder

Using needlenose pliers, grasp the

PCRs found in the LX and PX car-

metal drum axle (at the notch) on the

tridges and it is easily damaged.

large gear end of the waste hopper, while

Los Angeles

800-394-9900

818-316-0656

holding the hopper securely with the other

hand. Now, simply pull the pin straight out

and set it aside (See photo #2).

Atlanta

877-676-4223

770-516-9488

Dallas

877-499-4989

972-840-4989

Miami

800-595-4297

305-594-3396

Step 4

Remove the two wiper blade screws

Toronto

877-848-0818

905-702-9916

Grasp the drum gear, lift it up, and

with a Phillips screwdriver. Now, using

pull the drum straight out (See photo #3).

needlenose pliers, grasp the upward

Australia

877-848-0818

905-702-9916

Wrap the drum in protective cloth or paper

angled edge of the wiper blade, lifting it

and set it aside.

upwards and out (See photo #5).

AX T ECHNICAL G UIDE

T ECHNICAL S UPPORT (800) 394-9900 • (818) 316-0656

P AGE 1

AX ENGINE

Step 7

Step 10

Next, clean the wiper blade with a

Remove the end cap from the

waste hopper and clean old conductive

grease from the contact spring and

plate. Set the end cap aside and

remove the small white plastic mag

roller bushing (See photo #7).

Remove the fill plug, empty out

damp cloth (or, wiper blade cream)

any remaining toner and vacuum,

and set it aside. The waste hopper

making sure not to damage the lower

can now be emptied and vacuumed.

mylar strip. Clean all toner from the

In doing so, be careful not to damage

mag roller and wipe down with mag

the recovery blade.

roller cleaner. Insert seal. Note: The

black square guide (See photo #10)

Step 5

in the seal exit slot may be removed

Reassemble the waste hopper by

to facilitate seal installation, and then

following the above steps in reverse

reinserted.

order. Put the wiper blade back in and

tighten the two screws gently. Wipe all

toner from the PCR with the damp

Step 8

cloth and dry it with the soft, lint-free

Grasp the mag roller with your right

hand, while holding the toner hopper

securely with your left. Lift it upwards and

to the right (See photo #8).

cloth. Put the PCR back into its clips.

Install a new drum (or, a clean OEM

drum) and both drum axles. Set aside

Step 11

with the drum covered.

Re-install the doctor blade on the

Step 6

waste hopper and insert and tighten

screws. Drop the drive gear back into

Examine the toner hopper. There

its slot—with the notch on the flat area

are gears at one end and the bias con-

facing to the left (See photo #11).

nector at the other. One screw on each

Step 9

end holds the end caps. Both caps can

Remove the large white plastic

be removed if you’re curious, but only

bushing and drive gear from the left

the non-gear end needs to

(See photo #9). Then remove the two

be taken off. With this end facing you,

screws from the doctor blade and lift

remove the screw (See photo #6).

the blade out. Note: Avoid breaking off

the small locating pin on the left.

AX T ECHNICAL G UIDE

T ECHNICAL S UPPORT (800) 394-9900 • (818) 316-0656

P AGE 2

AX ENGINE

Now, put the long white plastic

Step 13

bushing on the left end of the mag

Replace the fill plug. Put the

roller by grasping the right end of the

small white plastic bushing on the

mag roller, lay it down into the hop-

right end of the mag roller. Now place

per and slide the shaft into the white

the end cap over the plug and align

plastic guide on the left. Turn the

the “D” shaped hole with the mag

mag roller until the flat side of the

roller shaft by turning the mag roller

shaft matches the flat area of the

gear on the other end. Insert and

gear, and insert into position.

tighten the last remaining screw.

Step 12

Step 14

Hold the toner hopper in one

Finally, fit the two halves together,

hand with your thumb on the shiny

aligning the springs on the toner

area of the mag roller to keep it in

hopper with the positioning pins on

position. A funnel will help you fill the

the waste hopper (See photo #13).

hopper from a toner bottle (See

Align the matching holes on each

photo #12).

end by pressing the springs against

their seats, and insert and press

home the locking pins.

Comparing Operating Specifications

OEM No.

Toner

Drum

PCR Shaft

Cartridge

OEM

PPM of Pages

OEM

Fill

Diameter

Length

PCR

Length

Type/Model

Ctg. #

@ 5%

Density

(grams)

(mm)

Rubber

(inches)

AX/5L

C3906A

2,500

1.46

140

245

Soft

9.54

PX/4L, 4P

92274A

3,000

1.52

160

257

Hard

9.46

VX/5P, 5MP C3903A

4,000

1.52

225

257

Soft

9.54

LX/2P

92275A

3,500

1.43

225

254

Hard

9.46

AX T ECHNICAL G UIDE

T ECHNICAL S UPPORT (800) 394-9900 • (818) 316-0656

P AGE 3

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: