THOMSON ROC 3205 instrukcja+ kody.PDF

ROC3205

User manual

ROC 3205

This universal remote control is compatible with the majority of television sets, DVD

players, satellite receivers and infrared controlled cable.

This remote control has already been programmed so that you can use it to control

most of the audio/video products made by the THOMSON group. Before attempting to

programme the remote control, try it out by using one of the methods described in this

user manual.The two CR2032 batteries are already fitted in the remote control. Refer

to the diagram on the cover to replace them when they are worn out.

Please keep this guide along with the code list (provided separately), so that you can

programme your remote control for use with other products.

1 - Description of

the key functions

1 Indicator lamp: the red indicator lamp lights up

when any key is pressed.

2 Product keys ( TV , DVD or SAT ): Used to

programme and control different products (TV,

satellite receiver, DVD player and so on).

3 SHIFT : activates the secondary key features

(indications in blue).

4 VOL- , VOL+ Increases ( + ) or decreases ( - ) the

volume of the TV set;

SHIFT + C / B : also allows you to navigate the

menus horizontally.

5 :Teletext On/Off in TV mode.

SHIFT + MENU : turns on the menu of the

selected products

6 G (rewind): Goes backward or advances

forward ( DVD )*.

7 RECORD : To record, press the RECORD key

twice.

8 Stop the disc ( DVD )*.

9 Number keys 0 to 9: these keys have the same

functions as those of your original remote and

are also used to enter the codes for different

products.

10 : stop page scrolling (videotext).

11 SETUP : Programmes the remote control.

12 POWER : On/Standby.

13 AV : For selecting an external source (SCART).

14 PROG+ , PROG- : Programmes zapping button

(received by the television set or the satellite

receiver); use to scroll vertically through menus.

SHIFT + / : also allow you to navigate the

menus vertically.

15 MUTE : Switches the TV sound off.

SHIFT + OK : confirms a selection.

16 :Teletext Off in TV mode.

SHIFT + EXIT : turns off the menu of the

selected product.

17 B (play): play a DVD disc DVD *.

18 F : fast forward ( DVD )*.

19 K : Suspends play and stops on an image*.

20 :Videotext inlay on TV picture.

21 Press this key first before you type in the 2-digit

channel number (except for Thomson group

products).

* The coloured buttons can be used to select

categories when teletext is activated, and specific

functions depending on the make.

SAT : satellite receiver.

3. Point the remote control towards the product and

try to turn it off by pressing the POWER ( 12 ) key.

If the product doesn’t turn off, you’ll need to

programme the remote control by one of the

methods described in chapter 3 .

SAT : satellite receiver.

4. While the indicator is lit, type in the subcode

(example: 1 for THOMSON).

5. Point the remote towards the product and try to

turn it off by pressing the POWER ( 12 ) key.

6. If the product you want to control turns off, press

the MUTE ( 15 ) key to save the subcode.

7. If the product doesn’t turn off, press the POWER

( 12 ) key repeatedly until the set switches off. Wait

approximately one second between key presses to

give the red indicator lamp ( 1 ) enough time to go

off and light up again. This will allow you to see

whether the product responds or not.

8. Immediately after the product to be controlled

turns off, press the MUTE ( 15 ) key to save the

subcode.

Note:

If you want to assign another type of product than those

mentioned on the remote control (with the exception of the

TV button which can only be used to control a television

set), begin by entering the code that corresponds to the

product you want to programme (a 3-digit code that you will

find in the code booklet – see method B ).

Example: if you want to control a satellite receiver with the

DVD key, begin by entering a satellite code (any satellite,

for example: 603 for a Thomson satellite receiver) then

begin the procedure.

2 - Testing the remote control

before you programme it

1. Turn on the product you want to control.

DVD : DVD player,

2. Press the product key ( 2 ) that corresponds to the

type of product you want to control:

TV : television set,

DVD : DVD player,

3 - Programming

the remote control

Method A – Fast programming

with 1-digit subcode

Before you start programming, you must find the subcode

of the product to be controlled (television set, satellite

receiver or DVD player).

Refer to the list provided with these instructions, page I of

the codes .

1. Turn on the product you want to control.

2. Hold down the SETUP ( 11 ) key until the red

indicator lamp ( 1 ) remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp flashes when this time is almost up, and then

goes off).

3. Press the product key ( 2 ) that corresponds to the

type of product you want to control:

TV : television set,

Checking the programming:

Your product should be ready to receive remote control

commands. Check to see that your remote functions

correctly by performing the test described on page 3.

Method B - 3-digit codes programming

Before you start programming, you must find the code for

the product to be controlled (television set, satellite receiver

or DVD player).

Refer to the list provided with these instructions, on page II

of the codes .

1. Turn on the product you want to control.

2. Hold down the SETUP ( 11 ) until the red indicator

lamp ( 1 ) remains lit (the indicator light remains on

for a few seconds to give you the time to proceed

with the following steps. The indicator lamp flashes

when this time is almost up, and then goes off).

3. Press the product key ( 2 ) that corresponds to the

type of product you want to control:

TV : television set,

Note:

If you want to assign another type of product than those

mentioned on the remote control, begin by entering a code

that corresponds to the product you want to programme (a

3-digit code that you will find in the code booklet – see

method B ).

Example: if you want to control a satellite receiver with the

DVD key, begin by entering a satellite code (any satellite,

for example: 603 for a Thomson satellite receiver) then

begin the procedure.

Checking the programming:

Your product should be ready to receive remote control

commands.Check to see that your remote functions

correctly by performing the test described on page 3.

Method D - Automatic code search

With this method, the remote scrolls through the full code

list by sending an IR signal to the product to be controlled

remotely.

1. Check that your product is on. If not, turn it on

manually.

2. Hold down the SETUP ( 11 ) key until the red

indicator lamp ( 1 ) remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp flashes when this time is almost up, and then

goes off).

3. Release the SETUP key.

4. Press the product key ( 2 ) corresponding to the type

of product you want to control: (for example TV ).

5. Press PROG+ ( 14 ). After a few seconds, the

remote begins to scroll through the code list at

approximately 1 code per second. Press PROG+

( 14 ) once again to slow down the test speed (1

code every 3 seconds). As soon as the product

changes channels, press the MUTE ( 15 ) key to save

the code and stop the remote from scrolling

through the list. If you have gone past the code, you

can go back to the previous code by pressing

PROG- ( 14 ) as many times as necessary (you can

go forward by pressing POWER ( 12 ) or PROG+

( 14 ). As soon as the product responds again, press

the MUTE ( 15 ) key to save the code.

Note:

If you want to assign another type of product than those

mentioned on the remote control, begin by entering a code

that corresponds to the product you want to programme (a

3-digit code that you will find in the code booklet – see

method B ).

Example: if you want to control a satellite receiver with the

DVD key, begin by entering a satellite code (any satellite,

for example: 603 for a Thomson satellite receiver) then

begin the procedure.

Method E - Programming for control

of a COMBO TV/VCR,TV/DVD)

Depending on the COMBO group (TV/VCR,VCR/DVD, etc.)

and the make, you will be required to enter a single code for

both devices in the COMBO, or to enter two codes, one code

per device. Consult the separate list to discover this.

Before you start programming, you must find the subcode

or code of the subset to be controlled (television or video

recorder).

Refer to the list supplied with this user manual (see page

subcodes or codes ).

SAT : satellite receiver.

4. While the indicator is lit, enter the 3-digit code

proposed for the product to be controlled

(example: 036 for THOMSON). The red indicator

then goes off if the code is correct or flashes, if the

code is not on the list.

5. Point the remote control towards the product and

try to turn it off by pressing the POWER ( 12 ) key.

6. If the product doesn’t turn off, repeat step 2, using

the next 3-digit code in the list. Try to turn off the

product by pressing POWER ( 12 ) key once.

Repeat this procedure until one of the 3-digit codes

works.

Checking the programming:

Your product should be ready to receive remote control

commands. Check to see that your remote functions

correctly by performing the test described on page 3.

Method C - Programming by means

of code retrieval

If none of the codes work, you may still be able to retrieve

the appropriate code.

1. Turn on the product you want to control.

2. Hold down the SETUP ( 11 ) key until the red

indicator lamp ( 1 ) remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp flashes when this time is almost up, and then

goes off).

3. Press the product key ( 2 ) that corresponds to the

type of product you want to control:

TV : television set,

SAT : satellite receiver.

4. Point the remote control towards the product and

try to turn it off by pressing the POWER ( 12 ) key.

5. If the appliance to be controlled switches off, press

the MUTE ( 15 ) key to memorise the code.

6. If the product does not turn off, press the POWER

( 12 ) key until the product switches off (up to 200

times).Wait approximately one second between key

presses to give the red indicator lamp ( 1 ) enough

time to go off and light up again.This will allow you

to see whether the product responds or not.

7. Immediately upon turning off the product to be

controlled, press the MUTE ( 15 ) key to save the

code.

DVD : DVD player,

1. Turn on the COMBO you want to control.

2. Hold down the SETUP ( 11 ) key until the red

indicator lamp ( 1 ) remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp flashes when this time is almost up, and then

goes off).

3. Press the TV ( 2 ) key, then follow one of the

programming methods ( A , B , C or D ) described

earlier.

4. If second code programming is required then repeat

steps 2 and 3 above.

6 - Controlling volume in

satellite and cable mode

For satellite systems with a volume control, you can

choose the product that the MUTE ( 15 ) and VOL ( 4 )

keys will control: the television volume or the volume

of the satellite or cable receiver.

To choose, proceed as follows:

1. Press the TV ( 2 ) key (the remote control must be

in TV mode for this procedure).

2. Hold down the SETUP ( 11 ) key until the red

indicator lamp ( 1 ) remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp flashes when this time is almost up, and then

goes off).

3. Release the SETUP ( 11 ) key.

4. Press the MUTE ( 15 ) key for around 8 seconds.

The indicator light will blink and then go off for

about 8 seconds before blinking once more and

then staying off.

5. If the remote previously controlled the television

volume in SAT mode, it will now control the

volume of the satellite receiver; if it previously

controlled the volume of the satellite receiver, it will

now control the television volume.

4 - How to retrieve

a programmed code

You may want to retrieve the code programmed in the

remote control.

1. Hold down the SETUP ( 11 ) key until the red

indicator lamp ( 1 ) remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp flashes when this time is almost up, and then

goes off).

2. Press the product key ( 2 ) that corresponds to the

type of product you want to control:

TV : television set,

DVD : DVD player,

7 - The NAVI LIGHT system

The THOMSON NAVI LIGHT navigation system allows you

easy access to the settings of your television set (TV) or your

video recorder (VCR) fitted with the THOMSON

NAVI LIGHT system provided that you have allocated the

DVD or SAT keys to the video recorder.

1. Switch on the product you want to control.

2. Select the type of product concerned ( TV , DVD or

SAT ). In the DVD position, make sure that the AV

mode is activated for the TV set (the SCART socket

must be selected).

3. Press the SHIFT ( 3 ) key once and then press the

MENU ( 5 ) key.

4. To travel through the setting menus, press the up,

down, left, right keys ( 4 and 14 ).

5. Confirm with OK ( 15 ).

6. Exit the menus by pressing the EXIT ( 16 ) key.

Note: The SHIFT (3) key remains on as long as light I is

lit. If this light goes out, you have to press the SHIFT key

again before using the navigation keys. To exit this mode,

press SHIFT a second time.

5 - Check the programming

- For a television or a satellite receiver: turn on and

off, then try to change channels using a digit key (9).

- DVD player: load a DVD and then press PLAY ( B )

( 18 ).

Try other remote control keys to find out which

functions you can control. If you think that not all of the

keys are active, try the programming Method B or C .

When you have retrieved the code of your product,

make note of it.

After battery replacement, you may have to

programme the remote control again.

TV CODE

DVD CODE

ENGLISH - Do not mix different types of batteries or new and old

batteries. Do not use rechargeable batteries. In order to avoid any risk

of explosion, observe polarities indicated inside the battery

compartment. Replace only with the type of batteries specified above.

Do not throw them into fire, do not recharge them. If you are not using

the remote control for a long period of time, remove the batteries.

Please respect the environment and prevailing regulations. Before you

dispose of batteries or accumulators, ask your dealer whether they are

subject to special recycling and if they will accept them for disposal.

SAT CODE

ROC 3205 / EN - pp - PB / abalis - rst / 07-2005

SAT : satellite receiver.

3. Press SETUP ( 11 ) again briefly. The red indicator

lamp flashes once.

4. Press the number keys ( 0 to 9 ) in ascending order

until the red indicator lamp ( 1 ) flashes once.

5. The digit which made the red indicator lamp ( 1 )

flash, is the first number of the 3-digit code. Please

make note of it.

6. Repeat step 4 to find out the two other numbers of

the code.

7. When the third number is found, the red indicator

lamp ( 1 ) goes off.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: