ACCUCEL 6_manual.pdf

TURNIGY ACCUCELL-6

BALANCE CHARGER/DISCHARGER

FOR NICD/NIMH/LITHIUM/PB BATTERIES

Operating Manual

Thank you for purchasing the TURNIGY. This is a rapid

charge/discharger with built in balancer, computerised with micr-

oprocessor and specialised operating software. Please read this

entire operating manual completely and attentively before using.

Features

Optimised operating software

When charging or discharging, it has an ‘AUTO’ function that sets the

feeding current automatically. Especially for Lithium batteries, it can prevent

the over-charging can lead to an explosion by users fault. Every program in

the unit is controlled with mutual links and communication for every possible

error so it introduces a maximum safety. These can be set at users option.

Special recharge plugsport for receiver,transmitter and igniter charger. And

for frequently used charger port such as multi purpose crocodile pin etc.

It provides most convenient balance charge port for Lithium batteries, with

separated 3,4,5,6 charge port, and external reverse connector.

High-power and high-performance circuit

It employs the circuit that has maximum output power of 50W. As a result it

can charge or discharge up to 15cells of NiCd/NiMH and 6 series of Lithium

batteries with maximum current of 5.0A. Furthermore the cooling system is

so efficient that can hold such a power without any trouble of running the

CPU or the operating program.

Individual voltage balancer for Lithium batteries insideh

It has an individual-cell-voltage balancer inside.This does not require any

extra balancer separately when charging Lithium batteries(Lilo/LiPO/LiFe)

for cell voltage balancing.

Balance individual cells on discharge

It also can monitor and balance individual cells of the Lithium battery pack

during the discharge process. If the voltage of any one cell varies abnormally,

the process will be stopped with the error message.

Accept various types of Lithium battery

It can accept three types of Lithium batterles- Lilo, LiPo and LiFe. They have

different characteristics by their chemistry. You can select any one of them

that you are going to process before the job. For their specifications,

refer‘Warnings and safety notes’section.

Lithium battery ‘Fast’and ‘Storage’mode

You can charge Lithium battery for special purposes. ‘Fast’charge reduces

the charging time of Lithium battery and ‘Storage’mode controls the final

voltage of the battery to be suit for long time storage.

Maximum safety

Delta-peak sensitivity: The automatic charge termination program works on

the principle of the Delta-peak voltage detection.(NiCd/NiMH)

Auto-charge current limit: When charging NiCd or NiMH at

‘AUTO’current mode, you can set the upper limit of change current

to avoid from high current charging. This is very useful when charg-

ing the low impedance and small capacity NiMH battery in

“AUTO’mode.

Capacity limit: The changing capacity always calculated by

multiple of the charging current and time. If the charging capacity

exceeds the limit the process will be terminated automatically when

you set the maximum value.

Temperature limit(*): The temperature of the battery on charging will

rise by its internal chemical reaction. If you set the limit of tempera-

ture the process will be expired forcibly when the limit has reached.

Processing time limit: you can also restrain the maximum process

time to prevent from any possible defect.

Input power monitor: To protect the car battery using as input power

from being damaged the voltage of it always monitored. If it dorps

below the lower limit the process will be ended automatically.

Automatic cooling fan: The electric cooling fan comes into action

automatically only when the internal temperature of the unit is

raised.

Data store/load

For users convenience it can store maximum 5 data of different

batteries. You can establish the data contains program setting of the

battery to charge or discharge continually. These data can be called

out at any time you need and the process can be executed without

program setting.

Cyclic charging/discharging

Perform 1 to 5 cycles of charge>discharge or discharge>charge

continually for battery refreshing and balancing.

Exterior of the unit

Lithium balance charge program connection diagram

WARNING

It will damage the charger if you connect your battery with the TURNIGY-

charger incorrectly. Please connect as shown in the following diagram

carefully.

Warnings and safety notes

�Never leave the charge unsupervised when it is connected to its power

supply. If any malfunction is observed immediately terminate the process and

refer to the operation manual.

�Keep away the unit from dust, damp, rain, heat direct sunshine and

vibration. Do not dorp it.

�The circuit of the unit is designed to be powered by a 10-18V DC only.

�This unit and the battery to charge or discharge should be set up on a

head-resistant, non-inflammable and non-conductive surface. Never place

them on a car seat, carpet or similar. Keep all the inflammable volatile materi-

als well away from operating area.

�Be sure to understand the information of the battery to be charged or

discharged accurately. If the program is set up incorrectly the battery can

severely be damaged. Especially Lithium battery can cause a fire or an

explosion by over-charging.

NiCd/NiMH voltage level:1.2V/cell

allowable fast charge current:1C~2C depends on the

performance of cell discharge voltage cut off level

0.85V/cell(NiCd), 1.0V/cell(NiMH)

Lilo voltage level:3.6V/cell

max.charge voltage:4.1V/cell

allowable fast charge current: 1C or less

min.discharge voltage cut off level:2.5V/cell or higher

LiPo voltage level:3.7V/cell

max.charge voltage:4.2V/cell

allowable fast charge current: 1C or less

discharge voltage cut off level:3.0V/cell or higher

Life voltage level:3.3V/cell

max.charge voltage:3.6V/cell

allowable fast charge current: 4C or less(e.g. A123M1)

discharge voltage cut off level:2.0V/cell or higher

Pb voltage level:2.0V/cell

(Lead-acid) max.charge voltage:2.46V/cell

allowable fast charge current:0.4C or less

discharge voltage cut off level:1.50V/cell or higher

�To avoid short-circuits between the charge lead, always connect the charge

cable to the unit first and only then to the battery to be charged or discharged.

Reverse the hsequence when disconnecting.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: