FinePix E550 SERVICE MANUAL.pdf
(
4312 KB
)
Pobierz
373919900 UNPDF
DIGITAL CAMERA
FinePix E550
SERVICE MANUAL
US/CA/EU/EG/GE/AS/CH/JP-Model
WARNING
THE COMPONENTS IDENTIFIED BY THE MARK
“
”
ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PLEASE REPLACE ONLY BY THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.
IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN
ELECTRICAL SHOCK.
FUJI PHOTO FILM CO., LTD.
Ref.No.: ZM00565-103
Printed in Japan 2005.10
FinePix E550 Service Manual
SAFETY CHECK-OUT
After correcting the original problem, perform the following
safety check before return the product to the customer.
1. Check the area of your repair for unsoldered or poorly
soldered connections. Check the entire board surface
for solder splasher and bridges.
7.
CAUTION:
FOR CONTINUED
PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH
SAME TYPE 2.5 AMPERES 125V
FUSE.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
2.5A 125V
RISK OF FIRE-
REPLACE FUSE
AS MARKED
ATTENTION:
AFIN D'ASSURER
UNE PROTECTION
PERMANENTE CONTRE LES
RISQUES D'INCENDIE,
REMPLACER UNIQUEMENT
PAR UN FUSIBLE DE MEME,
TYPE 2.5 AMPERES, 125 VOLTS.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.
Point them out to the customer and recommend their
replacement.
2.5A 125V
4. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer
and recommend their replacement.
8.
WARNING:
TO REDUCE THE ELECTRIC
SHOCK, BE CAREFUL TO
TOUCH THE PARTS.
5. Check the B + voltage to see it is at the values
specified.
6. Make leakage - current measurements to determine
that exposed parts are acceptably insulated from the
supply circuit before returning the product to the
customer.
WARNING!
HIGH VOLTAGE
2
FinePix E550 Service Manual
TABLE OF CONTENTS
TABLE CONTENTS
1. General ........................................................... 4
1-1. Product specification .............................................. 4
1-2. Explanation of Terms .............................................. 7
1-3. Names of External Components ............................ 8
4. Adjustments .................................................. 43
4-1. Important point Adjustment when
Replacing Major Parts .......................................... 43
4-2. Measuring Instruments Used ............................... 43
4-3. Use Jig list ............................................................ 43
4-4. Calibration method of pattern box ........................ 44
4-5. Adjusting soft installation ...................................... 44
4-5-1. Various downloading software
decompressions, preservation methods,
and notes ................................................ 44
4-5-2. Installation of DSC jig driver ................... 45
4-5-3. Adjusting soft initiation method ............... 45
4-6. Initial Settings of the Adjustment Software ........... 46
4-7. Starting the Adjustment Software ......................... 49
4-8. [R] : Flash Memory Reset ..................................... 52
4-9. [F4] : CCD Data Input ........................................... 54
4-10. [F5] : CAMERA Adjustment .................................. 56
4-11. [F6] : AF Adjustment ............................................. 60
4-12. [F7] : Flash Adjustment ......................................... 63
4-13. [F1] : Battery Voltage Adjustment ......................... 65
4-14. [F11] : Video Adjustment ...................................... 69
4-15. [F3] : LCD Adjustment .......................................... 71
4-16. [F8] : Firmware Download .................................... 73
4-17. [F12] : End Setting ................................................ 75
2. Disassembly ................................................... 9
2-1. Names of internal Components .............................. 9
2-2. Removing the R CABI ASSY ................................ 10
2-3. Removing the LCD CONST ................................. 11
2-4. Removing the INNER BLOCK .............................. 12
2-5. Removing the BATT HOLDER ............................. 12
2-6. Removing the PRO PWB ASSY and
LEAD E. CAP ....................................................... 13
2-7. Removing the TOP PANEL ASSY and
MODE PWB ASSY ............................................... 13
2-8. Removing the BATTERY LID ............................... 14
2-9. Removing the LENS ASSY .................................. 14
2-10. Removing the F CABI ASSY INNER PARTS ....... 15
2-11. Removing the SPEAKER ASSY ........................... 15
3. Schematics ................................................... 17
3-1. Cautions ............................................................... 17
3-2. Basic Block Names and Functions ....................... 17
3-3. Description of Main Block Functions .................... 18
3-3-1. Technical Overview ................................. 18
3-4. Block Diagram ...................................................... 19
3-5. Overall connection Diagram ................................. 20
3-6. Schematics ........................................................... 21
3-6-1. CAMERA BLOCK ................................... 21
3-6-2. DCDC BLOCK ........................................ 22
3-6-3. MOTOR BLOCK ..................................... 23
3-6-4. PROCESS BLOCK ................................. 24
3-6-5. AUIDO BLOCK ....................................... 25
3-6-6. IPS BLOCK ............................................. 26
3-6-7. JACK BLOCK ......................................... 27
3-6-8. KSW BLOCK .......................................... 28
3-6-9. LCD BLOCK ........................................... 29
3-6-10. STROBE BLOCK .................................... 30
3-6-11. VIDEO BLOCK ....................................... 31
3-6-12. XE BLOCK .............................................. 31
3-6-13. CCD FPC BLOCK ................................... 32
3-6-14. CS FPC BLOCK ..................................... 33
3-6-15. KEY FPC BLOCK ................................... 33
3-6-16. MODE FPC BLOCK ................................ 34
3-6-17. PARTNER BLOCK .................................. 35
3-6-18. MAIN CN BLOCK ................................... 36
3-6-19. PRO CN BLOCK ..................................... 36
3-7. Mounted Parts Diagrams ...................................... 37
3-7-1. CCD FPC ASSY ..................................... 37
3-7-2. CS FPC ASSY ........................................ 37
3-7-3. MODE FPC ASSY .................................. 38
3-7-4. MAIN PWB ASSY ................................... 39
3-7-5. PRO PWB ASSY .................................... 41
5. Inspection ..................................................... 79
5-1. Required Measuring Equipment ........................... 79
5-2. Connection of Measuring Equipment ................... 79
5-3. Inspection and Factory Settings ........................... 80
6. Parts List ....................................................... 82
6-1. Packing and Accessories ..................................... 82
6-1-1. US-model ................................................ 82
6-1-2. CA-model ................................................ 83
6-1-3. EU-model ................................................ 84
6-1-4. EG-model ................................................ 85
6-1-5. GE-model ................................................ 86
6-1-6. AS-model ................................................ 87
6-1-7. CH-model ................................................ 88
6-1-8. JP-model ................................................. 89
6-2. Mechanical parts .................................................. 90
6-2-1. US/CA/EU/EG/GE/AS/JP-model ............ 90
6-2-2. CH-model ................................................ 91
6-3. Electrical parts ...................................................... 92
7. Appendix ....................................................... 93
7-1. Function of display for Firmware Version ............ 93
7-2. List of Related Technical Updates Issued ............ 94
3
1. General
FinePix E550 Service Manual
1. General
1-1. Product specification
System
Model
Digital camera FinePix E550
Effective pixels
6.3 million pixels
CCD
1/1.7-inch Super CCD HR
Number of total pixels: 6.63 million pixels
Storage media
xD-Picture Card (16/32/64/128/256/512 MB)
File format
Still image: DCF-compliant
Compressed: Exif ver.2.2 JPEG, DPOF-compatible
* Design rule for Camera File System compliant DPOF compatible
Uncompressed: CCD-RAW (RAF)
Movie: AVI format, Motion JPEG
Audio: WAVE format, Monaural sound
Number of recorded pixels
Still image: 4048
×
3040 pixels/2848
×
2136 pixels/2048
×
1536 pixels/
1600
×
1200 pixels/640
×
480 pixels ( / / / / )
Movie:640
×
480 pixels/320
240 pixels ( / )
(30 frames per second with monaural sound)
×
Lens
Fujinon 4
×
zoom lens, F2.8-F5.6
Focal length
f=7.2 mm-28.8 mm
(Equivalent to approx. 32.5 mm-130 mm on a 35 mm camera)
Digital zoom
: approx. 1.4
×
/ : approx. 2.0
×
/ : approx. 2.5
×
/ : approx. 6.3
×
(4
×
optical zoom lens is used together: Max. zoom scale: 25.2
×
)
Focus
TTL contrast-type AF(CENTER), AF(MULTI), AF AREA, CONTINUOUS AF, MF
Focal range
Normal: Approx. 60 cm (2.0ft.) to infinity
Macro: Approx. 7.5 cm (3.0 in.) to 80 cm (2.6 ft.) (wide-angle)
Shutter speed
3 sec. to 1/2000 sec. (depend on Exposure mode)
Aperture
F2.8 to F8 10 steps in 1/3 EV increments Manual/Auto selectable
Sensitivity
: AUTO (Equivalent to ISO 80 to 640, depending on conditions)/
80/100/200/400/800*
/ / / /P/S/A/M: Equivalent to ISO 80/100/200/400/800*
(During setting CCD-RAW ISO 80/100/200/400)
* Resolution is set at “ ”, “ ” and “ ” for shots taken at ISO 800.
Photometry
TTL 64-zones metering Multi, Spot, Average
Exposure control
Program AE (
, P, , , , ), Shutter-priority AE, Aperture-priority AE, Manual
exposure
Exposure compensation
-2 EV to +2 EV in 1/3 EV-step increments (in Manual mode)
White balance
Auto ( , , , , )
Manual modes, 8 positions can be selected (P, S, A, M)
Viewfinder
Real image optical Approx. 77% coverage
LCD monitor
2.0-inches, Aspect ratio: 4:3; 154,000 pixels low temperature polysilicon TFT, Approx.
100% coverage
Flash type
Auto flash using flash control sensor
Effective range: Wide-angle: Approx. 0.6 m-4.5 m (2.0 ft.-14.8 ft.)
(Approx. 0.3 m-0.8 m (1.0 ft.-2.6 ft.): Macro)
Telephoto: Approx. 0.6 m-2.2 m (2.0 ft.-7.2 ft.)
Flash modes: Auto, Red-Eye Reduction, Forced Flash, Suppressed Flash, Slow
Synchro, Red-Eye Reduction + Slow Synchro
Self-timer
2 sec./10 sec.
Continuous shooting
Top 4-frame: Number of recorded frames: up to 4 frames
(at intervals as short as approx. 0.3 sec.)
Final 4-frame: Number of recorded frames:
last 4 frames before releasing the shutter button
(at intervals as short as approx. 0.3 sec.)
Long-period continuous shooting with 1600
1200 pixels mode:
Number of recorded frames: up to 40 frames
(at intervals as short as approx. 0.6 sec.)
×
Shooting functions
Best framing, Frame No. memory
Playback functions
Trimming, Automatic playback, Multi-frame playback, Voice memo
Other functions
PictBridge, Language (
, English, Francais, Deutsch, Espanol,
), FinePix photo
mode (F-mode), WEB camera, Discharge batteries
4
FinePix E550 Service Manual
1. General
Power Supply and Others
Power supply
Use one of the following:
• 2
AA-size Ni-MH (Nickel-Metal Hydride) batteries
• Rechargeable Battery NH-10 (sold separately)
• 2
AA-size alkaline batteries (sold separately)
• AC-3VW (PictureCradle CP-FXA10, sold separately)
• AC Power Adapter AC-3V (sold separately)
Guide to the number of
available frames for
battery operation
Battery Type
With LCD monitor ON
Ni-MH batteries 2300 mAh
Approx. 200 frames
According to the CIPA (Camera & Imaging Products Association) standard procedure for
measuring digital still camera battery consumption (extract):
When using Ni-MH batteries, use the batteries supplied with the camera. The storage
media should be xD-Picture Card.
Pictures should be taken at a temperature of 23
o
C, with the LCD monitor turned on, the
optical zoom moved from full wide-angle to full telephoto (or vice-versa) and back again to
its original position every 30 seconds, the flash used at full power every second shot and the
camera turned off and then on again once every 10 shots.
• Note: Because the number of available shots varies depending on the level of charge
in Ni-MH batteries, the figures shown here for the number of available shots
using batteries are not guaranteed.
The number of available shots will also decline at low temperatures.
Conditions for use
Temperature: 0
o
C to +40
o
C (+32
o
F to +104
o
F); 80% humidity or less (no condensation)
Camera dimensions
105 mm
63 mm
×
34.4 mm/4.1 in.
×
2.5 in.
×
1.4 in.
(W/H/D)
(not including accessories and attachments)
Camera mass (weight)
Approx. 200 g/7.1 oz. (not including accessories, batteries and xD-Picture Card)
Weight for photography
Approx. 260 g/9.2 oz. (including batteries and xD-Picture Card)
Accessories
AA-size Ni-MH Batteries (2)
16 MB, xD-Picture Card (1) Included with: Anti-static case (1)
Strap (1)
Terminal cover (1)
A/V cable (1) (plug (2.5 mm dia.) to pin-plug cable
×
2) (approx. 1.2 m (3.9 ft.))
USB cable (1) (approx. 1.2 m (3.9 ft.))
Cradle adapter for FinePix E550 (1)
Battery charger BC-NH01 (1)
CD-ROM (1) Software for FinePix AX
Owner’s Manual (1)
Optional accessories
xD-Picture Card
DPC-16 (16 MB)/DPC-32 (32 MB)/DPC-64 (64 MB)/DPC-128 (128 MB)/
DPC-256 (256 MB)/DPC-512 (512 MB)
AC Power Adapter AC-3V
Fujifilm Rechargeable Battery 2HR-3UF
Fujifilm Battery Charger with Battery BK-NH/BK-NH2 (With Euro type or UK type plug)
PictureCradle CP-FXA10
Rechargeable Battery NH-10
Soft Case SC-FXE01
Wide Conversion Lens WL-FXE01
Tele Conversion Lens TL-FXE01
Adapter Ring AR-FXE02
Image Memory Card Reader DPC-R1
• Compatible with Windows 98/98 SE, Windows Me, Windows 2000 Professional,
Windows XP or iMac, Mac OS 8.6 to 9.2.2, Mac OS X (10.1.2 to 10.2.2) and
models that support USB as standard.
• Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V,
4 MB to 128 MB.
PC Card Adapter DPC-AD
• Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V,
2 MB to 128 MB.
CompactFlash Card Adapter DPC-CF
• Windows 95/98/98 SE/Me/2000 Professional/XP
• Mac OS 8.6 to 9.2/X (10.1.2 to 10.1.5)
xD-Picture Card USB Drive DPC-UD1
• Compatible with xD-Picture Card of 16 MB to 512 MB
• Windows 98/98 SE/Me/2000 Professional/XP
• Mac OS 9.0 to 9.2/X (10.0.4 to 10.2.6)
5
×
×
×
Plik z chomika:
daarre
Inne pliki z tego folderu:
FinePix S2 Pro SERVICE MANUAL.pdf
(6643 KB)
FinePix F601 Zoom SERVICE MANUAL.pdf
(8764 KB)
FinePix 4900ZOOM PARTS LIST.pdf
(281 KB)
FinePix 4800Zoom SERVICE GUIDE.pdf
(4004 KB)
FinePix 4800Zoom PARTS LIST.pdf
(1768 KB)
Inne foldery tego chomika:
CANON
EPSON
JVC
KODAK
NIKON
Zgłoś jeśli
naruszono regulamin