Aluc.txt

85000 0 0 "Direc. X=0 Z=1"
85001 0 0 "Direction X=0 Z=1"
85010 0 0 "Nom du programme de tronçonnage"
85012 0 0 "Point de commutation G0 à G1"
85014 0 0 "Avance G1"
85016 0 0 "Position de reprise"
85018 0 0 "Décalage S1 en S2"
85020 0 0 "Appuyer 0=Non 1=Oui"
85030 0 0 "Position de prise en Z"
85032 0 0 "Position de butée en X"
85034 0 0 "Position finale en Z"
85036 0 0 "Position de dégagement en Z"
85038 0 0 "Position finale en Z Nouvelle barre"
85040 0 0 "Vitesse d'avance"
85042 0 0 "Temporisation chute derniere piece en sec."
85043 0 0 "Temporisation avance recuperateur en sec."
85044 0 0 "Derniere piece avant changement de barre "
85046 0 0 "0= Usinage derniere piece 1= Ejection piece"
85048 0 0 "0=Recuperateur 1=Non recuperee 2=Sous-programme derniere piece"
85049 0 0 "1= derniere piece non recuperee 2= derniere piece usinee "
85050 0 0 "Sous-programme de fin de barre" 
85052 0 0 "Sous-programme de changement de barre" 
85054 0 0 "Oscillation de broche a l'embarrage 0=off 1=on"
85056 0 0 "Attente de MX1 Fin Kupa"
85057 0 0 "Attente de MX2 Fin Kupa Start apres changement"
85058 0 0 "Attente lancement apres changement"
85060 0 0 " Utilisat."
85062 0 0 " Transf.%npiece"
85064 0 0 " Emb."
85066 0 0 " Emb.Kupa "
85068 0 0 " Emb.Emco "
85070 0 0 " Emb.%nIrco/FMB "
85071 0 0 " Emb.%nAutre "
85072 0 0 " Jauges %nd'Outils "
85074 0 0 " cor.out1"
85076 0 0 " cor.out2"
85078 0 0 " L1(X)_plus ...Fenetre de tolerance usure "
85080 0 0 " L1(X)_min ... Fenetre de tolerance usure "
85082 0 0 " L2(Z)_plus ...Fenetre de tolerance usure "
85084 0 0 " L2(Z)_min ... Fenetre de tolerance usure "
85086 0 0 " L1(X)_plus/min ...Limite de tolerance d'usure "
85088 0 0 " L2(Z)_plus/min ...Limite de tolerance d'usure "
85090 0 0 " Controle 0=L1(X)/L2(Z)  1=L1(X)  2=L2(Z)"
85100 0 0 "Tool station bar stop "
85102 0 0 "T number "
85104 0 0 "Tool correction bar stop "
85106 0 0 "D number "
85108 0 0 "New bar "
85110 0 0 "Bar end PRG "
85112 0 0 "Bar stop X "
85114 0 0 "Bar stop position in Z "
85116 0 0 "Bar stop Z "
85118 0 0 "Bar stop position new bar in Z "
85120 0 0 "New bar pos."
85122 0 0 "Safety in Z "
85124 0 0 "Dwell forwa."
85126 0 0 "Dwell t. for remnant drop down "
85128 0 0 "Dwell backw."
85130 0 0 "1=Barstop 2=Supsp. 3=Barloader "
85132 0 0 "Barfeed with "
85134 0 0 "0=no bar stop 1=bar stop"
85136 0 0 "New bar stop"
85138 0 0 "Oscilating "
85140 0 0 "1=ch.conv.2=p.ch.3=endprg.4=slide"
85142 0 0 "Bar end in"
85144 0 0 "only the 1st time(cycle twice)"
85146 0 0 "Part finish "
85148 0 0 "Kupa-%nLM_92"
85150 0 0 "End of bar"
85152 0 0 "Part chatcher forward "
85154 0 0 "Part slide forward"
85156 0 0 "Bar change activ - Waiting for input"
85158 0 0 "Barloder pushes forward ! - Waiting for input"