SonyDSC-T100.sm_level.3.pdf

DSC-T100

SERVICE MANUAL

LEVEL 3

US Model

Canadian Model

AEP Model

UK Model

E Model

Australian Model

Hong Kong Model

Chinese Model

Korea Model

Brazilian Model

Japanese Model

Tourist Model

Ver. 1.0 2007.02

Revision History

How to use

Acrobat Reader

Internal memory

ON BOARD

Photo: Silver

Link

SERVICE NOTE

PRINTED WIRING BOARDS

REPAIR PARTS LIST

SCHEMATIC DIAGRAMS

The components identified by

mark 0 or dotted line with

mark 0 are critical for safety.

Replace only with part num-

ber specified.

Les composants identifiés par une

marque 0 sont critiques pour la

sécurité.

Ne les remplacer que par une pièce

portant le numéro spécifié.

DIGITAL STILL CAMERA

DSC-T100_L3

2007B0500-1

Published by Kohda TEC

9-852-191-11

Sony EMCS Co.

Link

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH

MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered

connections. Check the entire board surface for solder splashes

and bridges.

2. Check the interboard wiring to ensure that no wires are

"pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly

transistors, that were installed during a previous repair. Point

them out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs

of deterioration. Point them out to the customer and

recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. FLEXIBLE Circuit Board Repairing

•

Unleaded solder

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•

Unleaded solder melts at a temperature about 40

C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350

Keep the temperature of the soldering iron around 270

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

during repairing.

•

Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

•

Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than

ordinary solder so use caution not to let solder bridges occur such

as on IC pins, etc.

•

Be careful not to apply force on the conductor when soldering

or unsoldering.

•

Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

DSC-T100_L3

— 2 —

TABLE OF CONTENTS

Section

Title

P a ge

1. SERVICE NOTE

1-4. Method for Copying or Erasing the Data in Internal

Memory ··········································································· 1-3

1-5. How to Write Data to Internal Memory ·························· 1-4

4. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS

4-2. Schematic Diagrams ························································ 4-3

4-3. Printed Wiring Boards ··················································· 4-19

4-4. Mounted Parts Location ················································ 4-25

5. REPAIR PARTS LIST

5-2. Electrical Parts List ························································· 5-6

DSC-T100_L3

— 3 —

1. SERVICE NOTE

1-4. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)

Note 1: When replacing the SY-171 board, erase the data in internal memory of the board before replacement.

Note 2: When replacing the SY-171 board, execute formatting and initialize the internal memory after replacement.

Method for Copying the Data in Internal Memory

Copy

Copies all images in the internal memory to a “Memory Stick Duo”.

1 Insert a “ Memory Stick Duo ” having 32MB or larger capacity.

2 Select [Copy] with v/V/b/B on the control button, then press z.

The message “ All data in internal memory will be copied ” appears.

3 Select [OK] with v, then press z.

Copying starts.

To cancel the copying

Select [Cancel] in step 3, then press z.

• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little

remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.

You cannot copy individual images.

• The original images in the internal memory are retained even after copying. To delete the contents of the

internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in

[ Internal Memory Tool].

• When you copy the data in the internal memory to the “Memory Stick Duo”, all the data will be copied.

You cannot choose a specific folder on the “Memory Stick Duo” as the destination for the data to be

copied.

• Even if you copy data, a DPOF (Print order) mark is not copied.

Method for Formatting the Internal Memory

This item does not appear when a “Memory Stick Duo” is inserted in the camera.

Format

Formats the internal memory.

• Note that formatting irrevocably erases all data in the internal memory, including even protected images.

1 Select [Format] with v/V/b/B on the control button, then press z.

The message “All data in internal memory will be erased” appears.

2 Select [OK] with v, then press z.

The format is complete.

To cancel the formatting

Select [Cancel] in step 2, then press z.

DSC-T100_L3

1-3

•

1-5. HOW TO WRITE DATA TO INTERNAL MEMORY

Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.

This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.

To change the setting, use the write enable tool “WriteEnableTool.exe”.

Data writing method

1) Connect the PC to the camera (USB mode: Mass Storage), and switch the driver to the “Sony Seus USB Driver”.

2) Start the Write Enable Tool and the SeusEX.

3) Click the [Activate Write Enable Mode] button of the Write Enable Tool.

4) Upon completion of the setting change, the following message will be displayed.

5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).

6) Write the data read out into the PC to the internal memory of the camera.

7) Disconnect the PC from the camera, and turn off the camera.

Note: By turning off the camera, the write enable setting is reset.

DSC-T100_L3

1-4E

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: