Gorset.pdf
(
4288 KB
)
Pobierz
303679621 UNPDF
(Afternoon) Tea Top
By Karin Arver, IchigoGirl
2009-08-27
Pattern and instructions for fitted top with pleated
detail.
Printing the pattern
: I made the pages in A4, but they should come out right on other sizes of paper
too if you make sure to choose “don’t scale” when you print it. Measure the test-square if you’re not
sure.
Size:
Equivalent to Burdastyle sz 36 (In the shops I always buy size 34 though, so check your
measurements to mine to be sure about the size). This pattern fits me (84cm bust, 67cm waist and
90cm hips, 165 cm tall, bra size 70B = 32B). The top is fitted, so you may need to alter the pattern to
fit if your measurements differ from mine, but it should be a bit forgiving since the top-part is gathered.
Alter the body in the side-seams and/or darts if necessary. Alter the top front in the middle of each cup
and the back top-part in the same part as you’ve altered the bottom back-part. Don’t forget to alter the
facing (pieces 5 and 6) if you alter the top-part of the pattern (pieces 3 and 4).
Remember that if you need the top to be for example 2cm’s wider, you only need to add 0,5cm’s to the
side seam or middle of each pattern-piece, as that adds up to 2cm in total.
You need:
•
Zipper or hook-and-eye-ribbon. (about 40cm’s long, depending on how long you want the top to be).
•
Material for the top (about 60cm’s should be enough, depending on fabric width).
•
Satin for pleated detail, (4cm wide x about 2m’s long)
•
Thread
Recommended fabrics:
Light wool, cotton, silk and silk-, cotton- or wool-blends. Unsuitable for
knits.
How to make the pleat:
http://www.burdastyle.com/techniques/make-a-pleated-trim
Cutting the material:
All pattern pieces include 1.5 cm’s seam allowance, as indicated on pattern.
1. Bodice front (cut 1, on fold)
2. Bodice back (cut 2)
3. Front yoke (cut 1, on fold)
4. Back yoke (cut 2)
5. Front facing (cut 1, on fold)
6. Back facing (cut 2)
7. Pleat detail (cut 1 strip of satin, 4cm’s wide, with fabric grain running lengthwise, to about 2,5x the
length of the top edge of the top = about 2m’s)
Preparation:
Place pattern pieces on fabric, making sure grainline is correct. Cut pieces and
transfer all markings to fabric.
Apply lightweight interfacing to the wrong sides of the facings (if the fabric is loose or very thin and
needs more stability). Don’t interface the seam-allowances.
Sewing:
1. Finish the edges of all pieces (zig-zag).
2. Stitch the darts on the front piece and back piece.
3. Stitch double lines for gathering about 3mm apart, just
outside the side-seam-marks of the top part of the front yoke
(piece no3). Use long stitches (5-6). Stitch two equivalent
lines on each side of the center of the front yoke.
4. Pin the front yoke to the back yoke (the side-seams). Gather the
side-seam-gathers on the front yoke to the same length as the
back yoke piece side, tie a knot a each end of the gathers and
distribute the gathers along the seam, pin and stitch. Remove the
gathering-seams.
5. Pin the bottom piece and the front piece
side-seams (piece no 1 and 2) and stitch.
6. Pin the bottom of the front yoke (piece no
3) and back yokes (piece no 4) to the top of
the bodice front- and back piece (piece no1
and no 2) right sides facing and stitch.
Make sure all the seams match up
(the side-seams and the yoke/bottom-piece
seams).
7. Gather the center front yoke gather to 5cm’s,
tie knots at
each end of the gather to keep the threads from slipping and
carefully stitch back and forth along the gather (in between the
gathering-stitch-lines) a few times, between the two gather-
threads. Remove the gathering-threads (the basting).
5. Make the pleated ruffle for the top
(Instructions here:
http://www.burdastyle.com/techniques/make-a-
pleated-trim) and pin it to the top of the front-
pieces (the yoke-part), starting in the center
front, in between the facing and the back pieces
(make sure everything goes the right way after
sewing, right sides should face each other with
the pleat in between!). Stitch and turn the right
way, so that the pleated ruffle’s top part sticks
out above the facing and fabric.
10. Press seam allowances open (not necessary next to the gathers). Also press a fold along the
seam-allowances of the center back, to make it easier to sew the zipper or hook-and-eye-ribbon.
11. Pin the zipper or hook-and-
eye-ribbon to the folded edge of
the center back-pieces. Make sure
it looks neat where the trim meets
the zipper/hook/eye-ribbon. You
can fold the end of the trim
underneath the facing to hide the
end if necessary. Stitch as close
to the zippertooth/hooks and eyes
as possible.
12. Top stitch along the pleated ruffle, on the right
side, a couple of mm’s from the edge of the top’s
fabric/the trim.
13. Hem as desired (I used an invisable hem-stitch on my sewing machine, but you could just fold and
stitch as you would on a blouse).
14. Secure the facing to the side-seams, center-front and if necessary center back with a few stitches
(by hand).
Finished!
(Just one more thing…. please please please upload images of your creation on Burdastyle!)
Plik z chomika:
sims159357
Inne pliki z tego folderu:
w_bka_11_05_40_wykroj bluzka z kwiatem.pdf
(110 KB)
w_ska_11_10_40_wykroj sukienka.pdf
(150 KB)
w_sca_11_06_40_wykroj spodnicado tanca brzucha.pdf
(234 KB)
w_ska_11_09_40_wykroj supienka vingag.pdf
(174 KB)
w_ska_11_08_40_wykroj sukienka rossmel.pdf
(249 KB)
Inne foldery tego chomika:
Aranże - Podkłady - Karaoke , kfn , midi , kar , mp3
Bajki i inne filmy dla dzieci
Camera
Ekwador 2002
Filmy
Zgłoś jeśli
naruszono regulamin