liebherr_escavator_instr_beta1.pdf

General

First read the instruction. If all is clear then cut out all pieces for the step, then fold them and hold

them together. If this is correct and works out, then glue.

If you encounter a problem or some mistake in this model, so please feel free to send me a mail (

chriess@vr-web.de ), referencing to this model. I answer it as soon as possible.

Also if my misspelling is so big, as you get nightmares.

Tools

Knife

Glue

Scissor

Patience

Music & a good Drink ;-) I prefer ..... uhm – are you mature ?

Some words to the model

Some sheets are to be printed out more than once. (e.g. Tires-sheet ). Read the instruction before.

Also read ? (Uhm good word for) the parts. Print out some spare-sheets if you think they are

difficult to build or cut, or even if you thing the instruction is badly writing ;-). (And write a mail ...)

All parts for the step should be inside a outlined box on the sheets.

If you see a red X inside a part, then this is a area to be cut out.

If you see one or more parts outlinded with red lines, so this means this are parts which aren't seen

from the outside. ( e.g. internal structure of the model )

Grey lines are construction-lines, they could help to cut, bend and fold.

If you see a big colored area beside some parts, with a small red line in the middle, this means, fold

and glue the parts to the area. Cut this parts after the glue is dry. (This are parts, that are seen from

both sides, so they need a colored backside.)

Not used Parts

all in use, except the diagonal supporters in the frame. (nothing to support, but they are really there)

Model-Pages

32 Pages, Page 2-5 printed twice.

14 Pages of Instruction

Rotatingassembly 1

Cut out the Parts [3 Parts]

Glue together. The ring schould

overlap the glueingflaps.

Crawler

Cut out the parts [12 Parts]

Glue the 3 biggest parts together

and than check to check. Than the 4

stiffener,level to the top.(look at the

square part to get a hint :-) insert the

hook.

Glue the square atop. This is the

gliding surface for the

rotatingassembly you have build.

Close it with the rotatingassembly

inside, glue the scissors at the

printed circle. Glue the cubes, they

are opposite of the scissors at the

underside of the frame. You build it

later. ( Believe me, i'am serious :-)

Tracks

Cut out and fold the parts [9 each

side]

Be aware of the glueingflaps of the

internal parts, they need to have a

small angle.

Cut out and glue the small parts

[ also 9 parts each side]

Take the rails and glue them

together, also the put the cylinder

and the hook in place.

You need a left and a right rail.

Then glue the rails with the bigger

parts under the crawler. At least

glue th rollers to the crawler.

Next cut out the parts of the

crawlerchain [15 parts each side]

Glue the crawlerchain and the

chainguide together. The small

rectangle is used to glue the

crawlerchain to the small rollers.

Glue the crawlerchain to the tracks

and the chainguide at the underside

of the tracks.

Backbone

Cut out the parts [9 Parts each side]

Glue the eyes so they will double

up the eyes of the big part. The flap

of the lower eye have to be loose

and directing into the front. It

covers later the frame-plate. If

needed use the strengtheners to

provide some strength to the eyes.

(If you want to glue the

excavatorarm to the body, so you

don't have to cut out the holes ! )

Counterweight

Cut out the parts [3 parts]

Glue the parts together, but let open. If the excavator is complete

you can add weight here to maintain stability. Hey this is a real

counterweight :-)

Frame

Cut out the parts [16 parts] You don't really need the tirangular

shaped supporter, no aggregates and engine so far in this model :-(

Glue the 3 middle crossmember

between the backbone. Stick or glue

the backbone into the counterweight

to maintain a proper fit. Glue the

bottom of the frame and the large

part as pictured here.

Than glue the backbone to the

bottom of the frame, add the other

crossmembers, and at last the last

piece between the backbone.

Silencer

Cut out the parts [3 parts]

Roll, fold, glue. Glue the silencer

not to the supporter. You have to do

that at last, with the almost finished

model.

Valveblock

Cut out [1 part] Fold and glue so

that beside the marking is a gap on

the upper surface. There you have

to stick the hydrauliclines into.

Casings, Motor, Cabin,

Hood

Cut out [13 parts]

Fold and glue.

You can glue the handrails, mirrors

now, but i think its better to do this

as the last. If you want to, so see the

last steps of the instruction.

Excavotorarm 1

Cut ot the parts, glue the two right parts backside [6 parts]

Glue the shell and the internal parts together, as shown here.

Glue the internal supporter into the arm, at last close it.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: