Table of Contents
JUMPER COMPONENT LOCATION DIAGRAM A
CHAPTER 1 INTRODUCTION 2
1-1 System features 3
1-2 Software power off control 4
1-3 Check list of the packing 5
1-4 Wake-On-LAN………………………………………………….6
CHAPTER 2 INSTALLATION 7
2-1 Installation procedures 7
2-2 CPU installation 8
2-3 System memory installation 20
2-4 SRAM installation 22
2-5 Other jumpers and connectors description 23
2-6 IDE driver installation 28
CHAPTER 3 AWARD BIOS SETUP 29
3-1 Update BIOS procedures 30
3-2 Award system BIOS configuration setup 31
APPENDIX A 56
ing this product from the supplier, or any of its distributors, vendors
local dealers, you are qualified for one year warranty.
This manual describes to configure the ATC-5030 mainboard for different environments. It's an overview of the layout and features of the ATC-5030 mainboard, and also provides information for you to change the configuration or system environment.
This manual is divided into two sections :
PART ONE includes page A and two chapters as following:
Page A contains layout diagram of the mainboard.
Please refer to it when you configure the system.
Chapter 1 is an overview of the ATC-5030 mainboard features
and packing items.
Chapter 2 describes how to upgrade and to change hardware
configurations such as memory size, CPU type, and
the lists of jumper settings and connectors.
PART TWO includes chapter 3 which contains Award BIOS
description..
Chapter 3 is the user's guide of the Award BIOS setup utility and
Flash ROM BIOS. The menu is shown in this chapter
will be indicated the value of the default settings.
Your system dealer will set up the ATC-5030 mainboard according to your demand of the computer. It means that the current settings of your ATC-5030 mainboard may not be the same as the defaults shown in this user's manual. If you need to change your configuration, please ask your dealer first. Be sure this will not void your system warranty, or ask your dealer to do it for you.
REMARK
Intel® is a registered trademark of Intel Corporation.
All other brands and product names are trademarks registered trademarks of their respective companies.
1-1 SYSTEM FEATURES
: Supports Intel Pentium (P54C) CPU operating at 90MHz to
200MHz & Intel Pentium MMXTM 166~233MHz (P55C), AMD
K5, AMD K6, Cyrix 6x86MXTM, 6x86L.
: INTEL 430TX PCIset.
: Using four 72-pin SIMM sockets, provides two banks of 64-bit wide path up to 256MB addressing page mode DRAMs.
: Using two 168-pin DIMM sockets for 3.3V SDRAM or 3.3V EDO DRAM module.
: Built-in 512KB PB SRAM on board
: Supporting four PCI bus master revision 2.1, 5V interface compliant and three 16-bit ISA slots.
: Dual Master IDE connectors support Ultra UMA/33 (33MB/sec transfer rate), up to four devices in two channels for connection of high capacity hard disk drive, CD-ROM, tape backup etc..
: AT style keyboard connector and header.
: The Ultra Multi-I/O chipset, integrated Keyboard controller.
Supporting Infrared transfer (IrDA TX/RX) connection.
One FDC port supports two devices up to 2.88MB
Two 16550A fast UARTs compatiable serial ports
One EPP/ECP mode parallel port
: Supporting Dual channel USB connection.
: Built-in Switching Voltage Regulator
: Supports ACPI Power Management - OSPM (OS directed power management)
: ATX and AT power connector
: PCB Dimension is 220mm x 230mm (8.66" x 9.0") with four layers designed.
1-2 SOFT-OFF CONTROL (option)
The ATC-5030 mainboard design supports Soft-Off Control feature through the SMM code in the BIOS under Windows 95, Windows 3.1x, and MS-DOS operation system environment. It needs to use ATX power supply. (please contact your supplier for this option)
Firstly, you should connect power switch cable (provided by ATX case supplier) to the PS_ON (CONN1) (next to FAN & socket 7 ) on the ATC-5030 mainboard.
In Windows 95, if you would like to soft power off the system, you just choose “shutdown the computer ?” in “Shut Down Windows“ from Windows 95, then push the Power Switch* (on ATX case), then system will be in soft off status directly. If you would like to restart the system, just press the button of the power switch, and the system will be power on.
* Default value (Power management of BIOS screen) is “Instant-off‘, you can change to ’Delay 4 Sec.‘, then you should push the Power Switch at least 4 seconds otherwise the system will be under SMI mode only.
In Windows 3.1x or MS-DOS, you should copy the program of “down.com” (you can find it in the diskette of IDE driver) into hard drive. When you would like to power off the system, just run this “down.com”, then the system will be shutdown and stay in standby status.
PS_ON
CONN1 FAN
CPU
Note : If you will leave your system several days, we suggest you use hardware mechanical power off to shutdown your system.
1-3 CHECK LIST OF THE PACKING
The ATC-5030 mainboard comes securely packed in a durable box and shipping carton. If any of the above items are missing or damaged, please contact your supplier.
Each ATC-5030 mainboard containing:
Q'TY Description
1 Mainboard : ATC-5030.
1 Diskette : Enhanced IDE driver (3.5").
Award system BIOS driver
Update Utility
1 Cable : Enhanced IDE connector.
1 Cable : F.D.D. connector.
1 Cable : Serial port.
1 Cable : Serial/Parallel.
1 Manual : User`s manual.
NOTE : Leave the ATC-5030 mainboard in its original packing until you are ready to install it.
1-5 Wake-On-LAN
The remote Wake-On-LAN mode of operation is a mechanism that uses Advanced Micro Device Magic Packet technology to power up a sleeping workstation on the network. This mechanism is accomplished when the LAN card receives a specific packet of information, called a Magic Packet, addressed to thenode on the network. For additional protection, Secure ON is an optional security feature that can be added to the Magic Packet that requires a password to power up the sleeping workstation. When the LAN card is in remote Wake-On-LAN mode, main system power can be shut down leaving power only for the LAN card and auxiliary power recondition.
The LAN card performs no network activities while in the remote Wake-On-LAN mode of operation-It only monitors the network for receipt of a Magic Packet. If a Magic Packet is addressed to the LAN card on the network, the LAN card wake up the system. If the Secure ON feature has been enabled, the password added to the Magic Packet is also verified prior to waking up the system.
You should select the LAN card also support WOL function. WOL has two protocol . That are INTEL and DEC. JP7 is set to recongize your LAN card is INTEL or DEC protocol.
WOL LAN card will provide a 3-pin line to connect the WOL connector on the mainboard.
WOL
JP7
INTEL
1-2
DEC
2-3
CHAPTER 2 INSTALLATION
2-1 INSTALLATION PROCEDURE
Before installing the computer, please prepare all components such as CPU, DRAM; peripherals such as hard disk devices, keyboard, CD-ROM drive; and accessories such as cables. Then, install the system as following :
1. Plug CPU, heat sink, cooling fan, and DRAM modules in
the ATC-5030 mainboard.
2. Set jumpers based on your configuration.
3. Plug add-on cards in PCI/ISA slots.
4. Connect cables to peripherals, power supply..
5. Make sure all components and devices are well
connected, turn on the power and setup System BIOS
based on your configuration.
6. Install peripheral, add-on card drivers and test them.
7. If all of above procedures are success, turn-off the power
then plug all of them into your computer case.
2-2 CPU INSTALLATION
ATC-5030 supports one Pentium level CPU.
It can auto detect CPU voltage value either single or dual CPU voltage power supply type without jumper setting. For installation, please notice CPU pin 1 must align with the ZIF socket 7 Pin 1 location. Before you install or upgrade your CPU, please read CPU guide from CPU manufacturer to make sure the CPU specification. Then choose the right installation in section 2-2-1 based on your CPU type/brand and follow the description to setup DIP Switch (SW1). If your CPU is not in the list of 2-2-1, please refer to 2-2-2 and 2-2-3 for installation. The ATC-5030 mainboard provides auto-detection function to detect CPU core voltages and CPU core voltages range from 2.1V to 3.5V.
2-2-1 CPU TYPE SELECTION
The DIP switch 1 on the ATC-5030 motherboard is to adjust
the CPU internal clocks by using external CPU frequencies
techniques for all brands of the CPU.
...
hrubertus