Zmieniarka CD w BMW E39.pdf

UPDATE: 12/98

CD Changer Installation Instructions for:

1999 BMW 5 Series Sedan (E39)

Mounting of CD Changer

In Factory Left-Rear Trunk Area

Part Description

Current E39 Kit P/N

82 11 1 469 911

QTY

New E39 Kit P/N

82 11 1 469 911

QTY

Main CD-C bracket

65 12 8 371 137

85 12 8 361 453

Main base bracket

65 12 8 361 452

M5x14 bolt

07 11 9 915 113

Clip nuts

61 13 1 372 033

Screw

07 11 9 916 946

Cap nut

51 71 1 934 930

Nylon insert nut

63 17 1 367 868

CD sub bracket

65 12 8 371 136

N/A

Installation Instruction P/N 99 00 0 001 756

BMW of North America, Inc.

Product & Service Engineering Dept.

December 1998

GENERAL INFORMATION

INTRODUCTION

These installation instructions were produced to give the installation technician all necessary

information to properly install the BMW CD Changer in the left side rear trunk area in all E39 sedan

vehicles.

These instructions were developed by the Product and Service Engineering Department of BMW

of North America, Inc. specifically for BMW vehicles and are not to be compared to any existing

products for vehicles other then BMW.

These instructions were complete and up to date at time of- issue. Any changes in the vehicle or

problems noted by the installer should be reported directly to BMW Product and Service

Engineering Department. Questions regarding this installation should be directed to the BMW

Technical Hotline.

Read all instructions carefully before proceeding with this installation. LH (left hand) and RH (right

hand) are referenced as determined from sitting in the driver's seat facing forward. Instructions

dealing with a common disassembly procedure are referenced to the TIS file found on the DIS

Tester.

REQUIRED TOOLS

Common hand tools

NECESSARY VEHICLE PREPARATION

Step 1

First, access the CD changer location in the left rear cargo area by opening the cosmetic cover

Step 2

Locate the CD changer audio and power/I-Bus cables. Position the cables to avoid pinching them

during the sub bracket installation process

Page 2

PREINSTALLATION

All vehicles with factory pre-wiring should have

the CD audio cable inserted into the (17 pin)

Radio Connector. Before starting installation of

the CD changer, check that the CD audio

cable is secured in place with the Lock Pin

(see Figure 1)

CD CHANGER PREPARATION

Shipping screws are installed on the bottom of

the CD changer to protect the unit during

shipment. Prior to installation, make sure you

remove the shipping screws and cover the

holes with the supplied adhesive seals as

described below.

1. Remove the 3 shipping screws from the

bottom of the CD changer (see Figure 2).

Store the 3 screws for future use; replace

3 screws only if a unit needs to be

returned for an exchange.

2. Cover the holes where the shipping screws

were installed with the 3 adhesive seals

supplied with the unit. (see Figure 2)

3. Change the position of the horizontal /

vertical Spring Pin on both sides of the CD

changer to the Vertical (h position (see

Figure 3). (The unit is shipped with the

Spring Pin in the Horizontal position.)

Page 3

4. To protect the Spring Pin, cover the Pin

area with the supplied Pin Label by

aligning the two diagonally opposite

holes with H and V positions (see

Figure 4).

INSTALLATION

5. Attach the mounting bracket to the CD

Changer using the mounting hardware

(M4) shipped with the CD Changer. Use

lower mounting holes for Left side and

higher ones for right side (see Figure 5).

7. Locate the CD Audio Cable (6-pin) and

Power/I-Bus Cable (3-pin), which are

terminated behind CD changer Trunk

Trim Cover in the left side (driver's side)

of the trunk (see Figure 6).

Page 4

8. Connect CD audio and Power/I-Bus

cables to CD changer (see Figure 7).

9. First, install a M5 bolt to front

threaded body nut loosely. Then,

install 4 other bolts to remaining 4

body nuts (see Figure 8).

10. Remove tray pocket from CD changer

Trunk Trim Cover and place CD changer

trunk trim bezel over CD changer (See

Figure 9).

FINAL INSTALLATION

11 Inspect all cable/wire routings and

secure with tie-wraps where necessary.

12 Test/operate per Owner's Manual.

13 Replace all interior components.

Page 5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: