Daewoo_Manual.pdf

DAEWOO

DAEWOO MANUAL

CONTENTS

APPLICATIONS

GENERAL OPERATION

SPECIAL FUNCTIONS

TIPS & HINTS

APPLICATIONS

MODEL

YEAR

CABLE

BROUGHAM II

ALL MODELS

ADC131(SWITCH 2)

CIELO

ALL MODELS

ADC131(SWITCH 2)

ESPERO

ALL MODELS

ADC131(SWITCH 2)

KALOS

ALL MODELS

ADC131(SWITCH 2)

ADC110-B

LACETTI

ALL MODELS

ADC110-B

LANOS

ALL MODELS

ADC131(SWITCH 2)

LEGANZA

ALL MODELS

ADC131(SWITCH 2)

LEGANZA 2000 MY

ALL MODELS

ADC128

LEZO

ALL MODELS

ADC131(SWITCH 2)

MAGNUS

ALL MODELS

ADC131(SWITCH 2)

MATIZ

ALL MODELS

ADC131(SWITCH 1)

ADC110-B

NUBIRA

ALL MODELS

ADC131(SWITCH 2)

NUBIRA 2000 MY

ALL MODELS

ADC128

NUBIRA II

ALL MODELS

ADC131(SWITCH 2)

ADC110-B

PRINCE

ALL MODELS

ADC131(SWITCH 2)

PRINCE II

ALL MODELS

ADC131(SWITCH 2)

REMAN

ALL MODELS

ADC131(SWITCH 2)

SUPER SALON

ALL MODELS

ADC131(SWITCH 2)

TACUMA

ALL MODELS

ADC131(SWITCH 2)

ADC110-B

ZETA

ALL MODELS

ADC131(SWITCH 2)

The cable used for DAEWOO has a switch to select for either

MATIZ or ALL OTHER DAEWOO vehicles.

MATIZ = POSITION 1

ALL OTHER VEHICLES = POSITION 2

NOTE : If the vehicle is fitted with OBD 16 Pin connector then use the

ADC110-B standard lead. These are only on 2000/01/02 model vehicles.

NOTE 2 : On a few vehicles dated 2000, a different protocol was used, which

meant a different cable is required. If no communication can be found on

the NUBIRA or LEGANZA Model Year 2000, then ADC128 should be used. All

later models use the standard ADC110-B OBD Cable.

GENERAL OPERATION

IMMOBILISER SYSTEM

INTRODUCTION

The immobiliser system provides theft protection using the ignition

key and transponder device. An LED is used to indicate the immobi-

liser status. The immobiliser control unit communicates to the engine

management unit when a valid key code is received and sends a se-

curity code to enable starting. If a valid key is used, the LED indi-

cates the correct key status, if an incorrect key is used a fault code

is set and the LED indicates an incorrect key status.

TRANSPONDER KEY

The transponder key consist of a 96bit crypto algorithm secret key

code which is transmitted via an aerial mounted around the ignition

key barrel.

CENTRAL LOCKING SYSTEM

INTRODUCTION

The remote keyless entry and anti-theft system fitted to the range of

Daewoo vehicles performs the following functions :-

• Remote unlocking of doors

• Sense of vehicle break in via doors, boot or bonnet.

• Sounding of warning device

• Locking of doors if the vehicle door or boot has not been

opened after 30 seconds of unlocking using the remote plip.

• Sense movement inside vehicle if ultrasonic sensors are fit-

ted.

COMPONENTS

• Remote entry module receiver control unit

• Security LED

• Boot open switch

• Boot tamper switch

• Front Door tamper switches

• Door open switches

• Central locking control unit

• Sounder

• Bonnet open switch

• Ultrasonic options (Optional)

GENERAL OPERATION

The remote control units lock and unlock the vehicle doors using ra-

dio frequency technology to the control unit. The range of control is

5-10 metres. When the doors are locked the indicator lamps flash

once, and when unlocked the lamps flash twice.

SECURITY INDICATOR

The security indicator mounted in the instrument panel indicates the

state of the security system. When the lock button is pressed, the

control system is armed and the LED flashes. The LED will now flash

until the control unit is disarmed.

CONTROL MODULE

The control module is mounted in the instrument panel, it controls

the whole system and has the ability for self diagnosis. If there is a

fault in the system the indicators will flash twice when the vehicle is

unlocked, with a 0.5 second delay between flashes. If the vehicle has

had an intrusion then the indicators will flash twice but with a 1.5

second delay between flashes.

NOTE : The immobiliser receiver does not need programming if re-

placed.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: