Ellen trousers instructions.pdf

(2612 KB) Pobierz
Microsoft Word - Ellen 9305.doc
Sewing Instructions for Pants
Sizes 34,36,38, 40,42,44
Fabric needed
Length of Pants (Sides): about 105 cm (41 inches)
The upper edge of the pants sits about 3 cm (1 ¼ inches) from the waistline
Tweed, 140 cm (55 inches) wide
Sizes 34,36,38: 1.50 meters (59 inches)
Sizes 40, 42,44: 1.55 meters (61 inches)
Size 46: 1.95 meters (76 ¾ inches)
Lining, 140 cm (55 inches) wide, 0.50 meters (19 ¾ inches) for all sizes
0.30 meters (11 ¾ inches) Vlieseline G785, 90 cm (35 ½ inches) wide
4 Buttons
1 Zip, Size 34,36,38: 8 cm, Size 40,42,44: 10 cm (4 inches)
Sewing thread
Preparing Pattern Pieces
All instructions for cutting can be found in the cutting chart above. Cut pattern pieces along the lines
according to the size you wish to sew.
The stitching line for the zip in part 1 is only depicted for a size 34. For all other sizes, draw the stitching
line at the same distance of the front middle as in the size 34. Pay attention to the length of the slit.
Cutting Out
The cutting instructions below show how to place the pattern pieces on the fabric. When placing the pieces
on the fabric, make sure that the grain lines depicted on the pattern pieces run parallel to the grain of the
fabric.
1 Front Pant Piece
2x
2 Back Pant Piece
2x
3 Front Waistband
4x
4 Back Waistband
4x
a.) Left underlap for slit:
For sizes 34,36,38: 9 cm
For sizes 40,42,44: 11cm long, 5 cm wide, finished width: 2.5 cm
7 Placket 6x
16 Pocket 3x
b.) 4 Belt Loops, about 32 cm long total, 7.5 cm wide (including seam allowances)
Lining:
1 Front Pant Piece ending at lining line
2x
16 Pocket
3x
Interfacing
All pieces that are depicted as grey areas on the copy paper should be cut as interfacing with the same grain
directions as the fabric pieces. Iron interfacing onto the wrong side of the outer waistband pieces and the
outer flap pieces.
Transferring Pattern Markings
Place the pieces with interfacing onto each other, right sides facing. Pin pattern pieces again.
194658084.017.png 194658084.018.png
With a tracing wheel and paper, transfer pattern markings (sewing and seam lines) as well as all the marked
lines on the pattern pieces (except for the grain markings) onto the wrong side of the fabric (detailed
instructions can be found on the pattern).
Transfer the stitching line for the zip, the front middle, wrap, base and flap base lines, the vertical lines and
the pleating lines onto the right side of the fabric, stitching by hand with wide stitches along those lines.
Sewing
Right Side
Wrong Side
Interfacing
Lining
When pinning and stitching the seams, the right sides of the fabric are facing. Secure beginning and end of
the seam line with reverse stitches.
1.) Darts
Fold back Pant Pieces so that the dart lines meet, right sides facing. Pin dart lines onto each other. Stitch,
starting at the upper edge, secure seam beginning with reverse stitches. Tie thread at the tip of the dart. (1)
Iron the dart to the back middle.
2.) Placket
Iron the seam allowances at the plackets folded to the inside (2). Pin plackets with the left side meeting the
base markings onto the front pant pieces, stitch the folded edge neatly onto the seam allowances. (3) Sew
about 7mm from the stitching line with contrasting thread, by hand.
(2)
(3)
3.) Flaps
Pin flap pieces with interfacing to the flap pieces without interfacing, right sides facing. Stitch, leaving the
base edge open. Trim seam allowances, cut at the rounded edges, cut deep towards the stitching line at the
194658084.019.png 194658084.020.png 194658084.001.png 194658084.002.png
edges. (4) Turn flaps. Pin edges, iron and stitch neatly. Sow in buttonhole, but do not cut yet. Pin flaps in
between the vertical lines of the upper edge of the front pant pieces, flaps pointing up. Stitch (5) . Cut seam
allowances of the base seam to 5 mm width. Iron flaps down, stitch neatly along the seam base line. Pin the
third flap between the vertical lines on the seam allowance of the right back pant piece.
(4)
(5)
4.) Side Seams
Place front pant pieces right sides facing onto the back pant pieces, pin side seams. Stitch. (6) Secure seam
beginning and end. Fold apart and iron seam allowances, de-baste. Fold over the slit allowances and iron to
the inside.
(6)
5.) Inner Leg Seams
Fold the pant pieces lengthwise, right side of fabric inside. Pin inner pant legs. Stitch. (7) Fold apart and
iron seam allowances. Turn pant legs, right side outside.
(7)
194658084.003.png 194658084.004.png 194658084.005.png 194658084.006.png 194658084.007.png
6.) Loops
Fold fabric strips in half lengthwise, right side inside. Stitch 2.5 cm from the wrap line. To turn, cut the
thread not too short on one end. Thread the thread into a darning needle and tie tightly. Pull needle with the
eye facing forward through the fabric tunnel (see drawings 25 and 26). Iron strip, stitch neatly and cut into
4 loops of equal length.
Place one loop each above the darts in the back and the middle of the front flap, the fourth loop should be
pinned to the left front pant piece at the same distance from the front middle.
7.) Crease, Back Pant Piece
Place pant pieces onto the ironing boards so that the inner leg seam meets the side seam, and the front
crease lies evenly. Iron crease into the back pant piece.
8.) Middle Seam, Front
De-baste the seam allowances of the front borders, the front middle seam and continuously of the back
middle seam.
Turn one pant leg, wrong side outside. Push pant legs into each other, right sides of fabric and inner pant
leg seams meet. Pin the front middle seam from the slit marking until the inner pant seam. Stitch. Secure
seam beginning and end (8). Pull pant legs apart.
(8)
9.) Slit for Zip
Ladies’ pants close from right to left. Pin over the border at the right front pant edge to the inside at the
marked front middle. At the left slit edge, pin the border to the inside, 5 mm next to the front middle, to
prevent the zip from showing. Make sure to cut the seam allowance at the end of the slit (arrow) until you
are about 5 mm from the seam. Iron edges. (9)
(9)
194658084.008.png 194658084.009.png 194658084.010.png 194658084.011.png
Pin the left slit edge close to the teeth of the zip onto the zip band and stitch tightly with the one-sided
zipper foot. (10)
(10)
Pin slit middle on middle. (11)
(11)
Pin the border of the right pant piece to the second zip band, not taking in the pants. Stitch zipper to the
border. (12) Coming from the right pant side to the right closure line at the marked stitching line from
above, stitch until you reach the beginning of the rounded edge, stitching the border. (13)
(12) (13)
Fold the underlap (a) lengthwise, right side inside. Stitch bottom edges onto each other. (14) Trim seam
allowances. Turn underlap. Pin and iron edges. Hold together and de-baste the open long edges. Pin the
underlap from the inside to the seam allowance of the left slit edge, so that the de-basted line lies on the
zipper band and the wrap line lies 3 cm from the front middle. (15)
194658084.012.png 194658084.013.png 194658084.014.png 194658084.015.png 194658084.016.png
Zgłoś jeśli naruszono regulamin