Bird Feeder 3.pdf
(
51 KB
)
Pobierz
Bird Table
Bird Table
This is the second type of bird table offered by Amateur Woodworker (the first one
was in the previous issue). The advantage of this particular model is that you can
easily put table scraps onto it, rather than the relatively expensive bird seed needed for
the other design. And let's face it, the birds are happy to get anything in the
winter...especially if you're a good cook!
Construction
Tools required:
jigsaw, sander
Wood required (Pine):
Description
Qty
Thickness Width Length
Back wall
1
3/4"
8"
14"
Front Wall
1
3/4"
8"
9"
Base
1
3/4"
8"
11"
Base support
1
3/4"
4"
9"
Roof
2
3/4"
7"
8"
Feeder stick (dowel) 1 3/8"
3/8" 3"
First, cut the back wall piece to shape, as shown in the diagram (left). Note that the
curve on the lower part of this piece does not need to be particularly accurate and can
be reshaped to suit your preferences. Once you have done this, you can then cut out
the front wall shape. The front wall has the same shape as the upper part of the back
wall, with the same (45 degree) roof pitch. Once the outside shape of the front wall
has been cut, sketch out the shape of the hole. Leave about 1" at either side of the
hole, so that the front of the roof is given adequate support. I went for a rather
simplistic design for this entrance way, but obviously the hole can be any shape you
wish -- perhaps a more decorative entrance will entice a better class of bird!?! Once
the entrance way has been cut (and sanded), drill a small 3/8" hole in the center of the
front wall, about 1" to 2" down from the roof's apex. Glue the small piece of dowel
into this hole so that the dowel sticks out. This is used to hang small pieces of fat out
for the birds -- a real delicacy!
Now cut out the curved shape of the base piece. This curve should begin somewhere
between 6" and 7" from the back wall end of the bird table (so that the curve has a
radius of about 4") and a smooth curve usually looks best. Once this is done, cut to
shape the base support piece. This can be any curve you wish, as long as there is a
right-angled support that will attach between the lower part of the back wall piece and
the underside of the base unit. Once this last piece has been cut to shape, it is time to
begin the actual construction.
Glue and screw the base unit into the back wall piece at a distance of 9"
from the top of the back wall (so between 9" and 9 3/4"). Then glue and
screw the base support piece into both the base and the back wall, thus
strengthening the construction. You can now glue and screw the front wall onto the
base, at a distance of 5" (so between 5" and 5 3/4") from the back wall.
Cut the roof pieces out, as shown in the diagram (right). Note that the long straight
edge that forms the apex of the roof must be cut at an angle of 45 degrees so that the
two roof pieces will sit flush against one another. Once both pieces have been cut to a
matching shape, and you are satisfied that they sit well on the roof, glue and screw
them into both the front and back walls.
All that remains is to sand the bird table thoroughly and then stain the wood to a
suitable color. To attach it to a tree, drive a long screw through the middle of the back
wall into the tree trunk.
Plik z chomika:
xporter
Inne pliki z tego folderu:
Woodwork Plans 1600 pages - 1600 projektow z drewna.pdf
(126007 KB)
201-500 - Woodwork - Plans.pdf
(86445 KB)
201-500 - Woodwork - Plans(1).pdf
(86445 KB)
Build a Garden Bench.pdf
(208 KB)
Piękny staromondy kredens.PDF
(3066 KB)
Inne foldery tego chomika:
123 otwiera wszystkie
ALAN LEE-- [ilustracje do Tolkiena]
bajki bajki
Balum Balum La Linea
Conan Niszczyciel (1984)
Zgłoś jeśli
naruszono regulamin